AMS Below article leader board Dec 14

usps express mail international flat rate envelope tracking number Comparisons are constantly being made between 3D printing and injection molding. Manufacturers of 3D printers and 3D printing materials strive to achieve the finish and detail that injection molding is known for, while enjoying the speed and cost benefits of 3D printing. In a study entitled “cari crack pes 2013” a group of researchers works to optimize the process parameters of 3D printed parts, comparing them with samples made with injection molding.

combustion 2008 for mac keygen The work focuses on improving the tensile mechanical properties of the 3D printed samples and investigating the impact of the process on the rheological and thermal properties. In particular, the researchers direct attention toward the printing order of three-dimensional samples, printed in a batch or individually.

nebim v3 crack The researchers used PLA for both the 3D printed and injection molded samples. Thermogravimetric analysis (TGA) was performed on the samples, as was calorimetric analysis. Two sets of samples were created for comparison, with the 3D printed samples being printed on an Ultimaker 2 3D printer.

crack do gry emergency 2012 chomikuj “The influence of the raster angle (the direction of raster with respect to the loading stress direction), build orientation (horizontal or vertical), and printing order on the mechanical properties of PLA were investigated,” the researchers state. “Default FDM parts in Ultimaker2 were made with a crisscross raster in which the orientation of the beads alternated from +45° to −45° from layer to layer. As the FDM software defaults to this raster, this orientation could be considered a [0°/90°] orientation if the part were rotated through 45°.”

come mettere la crack nei giochi Dumbell samples were printed with three different orientations. X samples were constructed horizontally with a raster orientation of 45°/+45°, # samples were built horizontally with a raster orientation of 0°/+90°, and H samples were manufactured vertically with a raster orientation of 0°/+90°. The first set of samples, consisting of 15 prints, was manufactured simultaneously, while the second set was manufactured one by one. Rheological measurements and tensile tests were then carried out.

boilsoft asf converter keygen

best zip password cracker software Before performing the mechanical tests, the samples were weighed.

butterfly cycle rack “There were three different weight values; the specimens produced by injection molding demonstrated a higher weight compared with specimens made by FDM (1.5 g),” the researchers continue. “The FDM specimens printed simultaneously demonstrated the lowest weight value (1.41 and 1.38 g) and the FDM specimens printed individually demonstrated a moderate weight value (1.44 and 1.42 g). This difference in weight between 3D specimens may be explained by intermolecular diffusion at the interface of filament layers.”

crack pre workout gebruik Since the weight of the specimens varied, the mechanical properties were also impacted.

crack simpson krustyland android “It can be noted that injection-molded samples have highest tensile modulus (1580 MPa), with a large standard deviation (±130) because of the heterogeneous thermal degradation between the different samples,” the researchers add. “Simultaneously printed samples reach a maximum of 1110 MPa for #-PLA, while a minimum of 984 MPa was recorded for X-PLA. This can be related to the fact that for samples printed at raster angles of 0°/90°, the filaments were oriented parallel to the load direction, producing the strongest samples. In samples printed at −45°/+45°, there was a finite angle between the printed microstructural elements and the load direction.”

movavi video converter crack 14 PLA has low thermal stability, so during injection molding, the samples were subject to major thermal degradation. The 3D printed samples did not suffer the same fate due to the short time the filament was in the nozzle. The researchers found that the samples 3D printed individually had better mechanical properties than those 3D printed simultaneously.

rival crock pot replacement lid scvp609h “In the same time, samples with a raster angle of 0°/90° demonstrated better properties than samples produced with a raster angle of −45°/+45°,” the researchers conclude. “Vertically printed samples with a raster angle of 0°/90° demonstrate interesting results, but these samples need a support during manufacturing and then require postprocessing due to the burr generated.”

portsmouth northsea christmas cracker meet Authors of the paper include Haroutioun Askanian, Daniel Muranaka de Lima, Sophie Commereuc and Vincent Verney.

facebook hacker pro crack file download Discuss this and other 3D printing topics at maywood firecracker tournament 2014 or share your thoughts below. 

crate and barrel pot rack bamboo  

Facebook Comments





Stay up-to-date on all the latest news from the 3D printing industry and receive information and offers from third party vendors.
  • This field is for validation purposes and should be left unchanged.

3DPRINT.COM HIGHLIGHTS & RESOURCES

prinergy evo keygen chevrolet citation steering rack Tagged with:


Print Services

Subscribe To Our Newsletter

Subscribe To Our Newsletter

ninja school 4 crack mien phi Join our mailing list to receive the latest news and updates from our 3DPrint.com.

You have Successfully Subscribed!